INNO Instrument 130 Items

The INNO Instrument IN-SS-40mm fiber splice protection sleeve is a 40 mm heat-shrink sleeve designed to reinforce single-fiber fusion splices. A stainless steel strength member helps prevent bending while the clear outer tube allows inspection of the splice during installation.

The INNO Instrument IN-RD-40mm ribbon fiber protection sleeve provides environmental and mechanical protection for ribbon fiber fusion splices. The 40 mm heat-shrink sleeve incorporates a double ceramic rod structure that maintains alignment and rigidity during the shrinking process.

The INNO Instrument IN-RS-40mm ribbon fiber splice protection sleeve is a 40 mm heat-shrink sleeve designed to protect ribbon fiber fusion splices. The sleeve incorporates a single ceramic reinforcement rod for structural support and alignment protection after splicing. A clear heat-shrinkable outer tube combined with an internal EVA adhesive liner.

INNO Instrument V30 Optical Multi Meter combines optical power measurement, visual fault location, and cable continuity testing in a handheld fiber optic test instrument designed for telecommunications installation and maintenance environments.

The INNO Instrument V20 Fiber Optic Inspection Microscope is a handheld USB inspection probe designed for evaluating optical connector end-faces during fiber installation and maintenance. The V20 microscope provides dual 200x and 360x magnification, integrated LED illumination, and a VGA imaging sensor for connector inspection and documentation.

The INNO Instrument VIEW600 OTDR is a modular fiber Optical Time Domain Reflectometer configured with a three-wavelength OTDR module supporting 1310 nm, 1550 nm, and a 1625 nm live testing port. This provides dynamic range performance of 39 dB, 38 dB, and 39 dB for characterization of metro, access, and FTTx fiber networks.

The INNO Instrument View Mini 2 OTDR (MINI2-SMF2) is a handheld optical time domain reflectometer designed for fiber optic maintenance and live network testing. This configuration includes a 1625nm filtered live port with a 30dB dynamic range for in-service fiber analysis without service interruption.

INNO Instrument View Mini 2 OTDR kit (MINI2-SMF1) for last-mile and FTTH fiber testing with 1310/1550nm, 32/30dB (SMF1) performance. Features a 5-inch touch LCD, built-in VFL and light source, 8GB storage, and up to 12-hour battery operation. V-20 microscope not included.

The INNO Instrument SC-SM-APC-30 is a 10-pack of SC-type single-mode splice-on connectors designed for 3.0mm fiber cables. Featuring APC polish and pre-polished factory ferrules, these connectors support fusion splice termination with low insertion loss and high return loss performance.

The INNO Instrument SC-SM-UPC-30 is a 10-pack of SC/UPC single-mode splice-on connectors designed for 3.0mm fiber cables. Each connector is factory pre-cleaved and pre-polished to support consistent optical performance, with typical insertion loss of 0.15 dB and return loss ≥55 dB.

The INNO Instrument SC-SM-APC-09 is a field-installable SC/APC singlemode splice-on connector supplied in 10 a pack. Designed for fusion splicer termination, the connector houses and protects the fusion splice within the connector body, eliminating separate splice trays. The cleaved and polished ferrule supports repeatable field assembly.

The INNO Instrument SC-SM-UPC-09 is a 10-pack of single-mode SC/UPC splice-on connectors for 900µm fiber. Designed for fusion splicer termination, these connectors eliminate polishing, adhesives, and mechanical splicing. With typical ≤0.2 dB insertion loss and ≥55 dB return loss, they support G.652D and G.657A2 fiber types.

The INNO Instrument E-50 Electrodes are replacement consumables designed for use with compatible INNO fusion splicers. Supplied as a matched pair, they generate the controlled electrical arc required for fiber fusion. The E-50 set supports routine maintenance and consistent splicing performance within fiber optic installation and service workflows.

The INNO Instrument CG-24 Cooling Tray is a standard accessory designed for the INNO Instrument A3 Fusion Splicer. It provides a dedicated, heat-resistant surface for fiber optic protection sleeves immediately after oven heating.

The INNO Instrument CG-23 Cooling Tray is an accessory designed for use with INNO View Pro series fusion splicers. It provides a dedicated location to position heat-shrink protection sleeves after the heating cycle. Compatible with View 3 PRO, View 5 PRO, and View 8 PRO models.

The INNO Instrument FH Series Universal Fiber Holder is an accessory designed for INNO fusion splicers to position and secure optical fibers during splicing. The holder supports multiple fiber preparation types and provides stable alignment inside the splicer. Variant options support different splicer models and left or right holder configurations.

The INNO Instrument TS Pro Thermal Stripper is designed for removing coating and jacket from optic fibers, supporting single fiber up to 12 ribbon fibers. It accommodates coating diameters from 200 μm to 400 μm and provides selectable heating modes with controlled temperature settings.

The INNO Instrument VIEW 12R MAX is a 12-fiber ribbon fusion splicer using clad alignment technology and a 5.0-inch full-touch LCD interface. It supports 1–12 fiber splicing for SM, MM, DS, and NZDS fibers with integrated heater and included V12 cleaver kit.

The INNO Instrument VIEW 12R Pro is a 12-fiber ribbon fusion splicer with motorized clamp alignment, 5-inch touch LCD, integrated heat oven, and Nano-SIM IoT/GPS support. It stores up to 10,000 splice records for ribbon and single-fiber applications.

INNO Instrument View 8X is a single-fiber core alignment fusion splicer kit for SM, MM, DS, and NZDS fibers. It features ultrafast splice/heating cycles, a 5.0” full-touch display, automatic arc calibration, and IoT/GPS functions for tracking and device management.

The INNO Instrument View 5X is a core alignment fusion splicer designed for single-fiber applications across SM, MM, DS, and NZDS fibers. This kit includes the V12 cleaver, integrated heater, 5.0” touchscreen, IoT & GPS capability, battery, and carrying case.

The INNO Instrument VIEW 3X is an Active V-Groove Cladding Alignment Fusion Splicer designed for single-fiber splicing across SM, MM, DS, and NZDS fibers. This standard OEM kit includes the V12 cleaver and integrated heater, with embedded IoT, GPS, and View Pro Manager cloud connectivity for project and device management.

The INNO Instrument M9+ is a compact core alignment fusion splicer for single fiber SM, MM, DS, and NZDS applications. It features ultrafast splice and heating cycles, a 4.3-inch full touch LCD, automatic arc calibration, and integrated heater in a field-ready kit.

INNO Instrument M7+ compact fusion splicer kit with Active V-Groove cladding alignment and a 4.3" full-touch display. Supports single-fiber SM/MM/DS/NZDS splicing, quick splice/heating cycles, and data output via USB-C or View Pro Manager cloud.

The INNO Instrument A3 is a clad alignment arc fusion splicer designed for single-fiber splicing across SM, MM, DS, and NZDS fiber types. It features a 4.3-inch color LCD touch screen, active 4-motor alignment, and quick 7-second splice time in SM mode. This new kit configuration includes the V1 fiber cleaver and standard accessories for field deployment.