Network, Cable & Fiber Testers 787 Items

EA Technology CS2 CableSniffer delivers decisive underground LV cable fault location by capturing insulation breakdown gases, enabling faster pinpointing, fewer excavations, and confident field diagnostics with real-time ppm detection.

VIAVI 3Z-RFV-AAT-2000 antenna alignment tool streamlines antenna and microwave alignment with an integrated touchscreen, onboard camera, GPS/GLONASS positioning, and Bluetooth connectivity for field-ready deployment.

Fluke Networks DSX2-5000 certifies installed copper cabling through the Versiv 2 platform with DSX-5000 measurement modules for structured network testing.

EXFO FTB-1v2 OTDR kit with installed FTBx-730C-SM8-OPM-EA module for fiber link testing, including iOLM operation and built-in PM/VFL hardware.

INNO Instrument FH-SOC fusion splicer SOC holder for use with compatible INNO Instrument fusion splicers, including View 12R, View 12R PRO, View 3 PRO, and M Series.

INNO Instrument FH-Single Fusion Series fiber holder for 900 µm single fiber in detachable M Series fusion splicer applications.

The INNO Instrument Ribbon Holder are fiber ribbon holders designed for use with INNO Instrument View12R and View12R PRO fusion splicers. The holder supports 250 µm ribbon fiber during the splicing process, maintaining fiber alignment and stability within the splicer. Its detachable design allows quick installation and removal when preparing ribbon fibers for fusion splicing.

The INNO Instrument  Universal Fiber Holder is an accessory designed for INNO fusion splicers to position and secure optical fibers during splicing. The holder supports multiple fiber preparation types and provides stable alignment inside the splicer. Variant options support different splicer models and left or right holder configurations.

INNO Instrument V30 Optical Multi Meter combines optical power measurement, visual fault location, and cable continuity testing in a handheld fiber optic test instrument designed for telecommunications installation and maintenance environments.

The INNO Instrument V20 Fiber Optic Inspection Microscope is a handheld USB inspection probe designed for evaluating optical connector end-faces during fiber installation and maintenance. The V20 microscope provides dual 200x and 360x magnification, integrated LED illumination, and a VGA imaging sensor for connector inspection and documentation.

The INNO Instrument VIEW600 OTDR is a modular fiber Optical Time Domain Reflectometer configured with a three-wavelength OTDR module supporting 1310 nm, 1550 nm, and a 1625 nm live testing port. This provides dynamic range performance of 39 dB, 38 dB, and 39 dB for characterization of metro, access, and FTTx fiber networks.

The INNO Instrument View Mini 2 OTDR (MINI2-SMF2) is a handheld optical time domain reflectometer designed for fiber optic maintenance and live network testing. This configuration includes a 1625nm filtered live port with a 30dB dynamic range for in-service fiber analysis without service interruption.

INNO Instrument View Mini 2 OTDR kit (MINI2-SMF1) for last-mile and FTTH fiber testing with 1310/1550nm, 32/30dB (SMF1) performance. Features a 5-inch touch LCD, built-in VFL and light source, 8GB storage, and up to 12-hour battery operation. V-20 microscope not included.

The INNO Instrument CG-24 Cooling Tray is a standard accessory designed for the INNO Instrument A3 Fusion Splicer. It provides a dedicated, heat-resistant surface for fiber optic protection sleeves immediately after oven heating.

The INNO Instrument CG-23 Cooling Tray is an accessory designed for use with INNO View Pro series fusion splicers. It provides a dedicated location to position heat-shrink protection sleeves after the heating cycle. Compatible with View 3 PRO, View 5 PRO, and View 8 PRO models.

The Fluke Networks LinkIQ LIQ-KIT-FMC Cable & Network Tester Kit verifies twisted pair and fiber performance up to 10GBASE-T and supports network troubleshooting. It provides frequency-based bandwidth validation, wiremap, distance to fault, IPv4/IPv6 ping, nearest switch diagnostics, and PoE testing, with RJ-45, USB, and SFP connectivity.

The Fluke Networks DSX-CHA021S is a set of two M12D 4-position channel adapters designed for use with DSX Series CableAnalyzer systems. These adapters enable channel testing and certification of installed M12-D links supporting TIA Cat 5e and ISO Class D requirements, including verification of 100BASE-TX transmission performance.

The INNO Instrument TS Pro Thermal Stripper is designed for removing coating and jacket from optic fibers, supporting single fiber up to 12 ribbon fibers. It accommodates coating diameters from 200 μm to 400 μm and provides selectable heating modes with controlled temperature settings.

The INNO Instrument VIEW 12R MAX is a 12-fiber ribbon fusion splicer using clad alignment technology and a 5.0-inch full-touch LCD interface. It supports 1–12 fiber splicing for SM, MM, DS, and NZDS fibers with integrated heater and included V12 cleaver kit.

The INNO Instrument VIEW 12R Pro is a 12-fiber ribbon fusion splicer with motorized clamp alignment, 5-inch touch LCD, integrated heat oven, and Nano-SIM IoT/GPS support. It stores up to 10,000 splice records for ribbon and single-fiber applications.

The Fluke Networks DSX-AXTERM Link Terminator set includes two alien crosstalk link terminators designed for use with compatible DSX series platforms. These terminators provide crosstalk protection and are supplied as a packaged quantity of two units.

INNO Instrument View 8X is a single-fiber core alignment fusion splicer kit for SM, MM, DS, and NZDS fibers. It features ultrafast splice/heating cycles, a 5.0” full-touch display, automatic arc calibration, and IoT/GPS functions for tracking and device management.

The INNO Instrument View 5X is a core alignment fusion splicer designed for single-fiber applications across SM, MM, DS, and NZDS fibers. This kit includes the V12 cleaver, integrated heater, 5.0” touchscreen, IoT & GPS capability, battery, and carrying case.

The INNO Instrument VIEW 3X is an Active V-Groove Cladding Alignment Fusion Splicer designed for single-fiber splicing across SM, MM, DS, and NZDS fibers. This standard OEM kit includes the V12 cleaver and integrated heater, with embedded IoT, GPS, and View Pro Manager cloud connectivity for project and device management.

The INNO Instrument M9+ is a compact core alignment fusion splicer for single fiber SM, MM, DS, and NZDS applications. It features ultrafast splice and heating cycles, a 4.3-inch full touch LCD, automatic arc calibration, and integrated heater in a field-ready kit.