Search results for: 'requiring'

The Struthers-Dunn W88AHPX-36 is a hermetically sealed 3PDT plug-in relay from the 88HP Series, rated 10A and configured for 120VAC operation. It features an 11-pin octal base and a sealed gray metal enclosure designed to prevent contamination and corrosion.

The Appleton ST-4575 is a 3/4" 45° liquidtight connector designed for use with liquidtight flexible metal conduit (LFMC). This ST Series plain throat fitting provides a dependable connection while sealing out oil, water, dust, dirt, and fumes. Constructed with a malleable iron body and finished with zinc electroplate, chromate, and epoxy powder coat, it is suitable for wet locations and Class I, Division 2 environments.

Industrial multimeter service kit combining the Fluke 179 True-RMS digital multimeter and Fluke 323 True-RMS clamp meter. Designed for troubleshooting electrical and electronic systems, with voltage measurement up to 1000 V AC/DC and AC current measurement up to 400 A.

The Allen-Bradley 700-HK36A1 is a slim line plug-in relay with a 120V AC control voltage and one SPDT change-over contact. It supports a nominal current of 16 A and uses silver nickel contacts. Designed for plug-in connections, it is suitable for industrial control applications requiring compact relay solutions.

The Universal 447-LR-TC-P is a 120V magnetic fluorescent ballast designed to operate two lamps in trigger-start configurations. It supports F20T12, F15T8, and F15T12 lamps and features a low power factor, lag-type circuit. UL and CSA certifications support indoor and Type 1 outdoor use.

The Eaton H2006B-3 is a Freedom NEMA heater coil set designed for thermal overload protection in motor control applications. This Class 20 standard trip heater pack supports selectable full load current settings from 1.79A to 2.9A via dial positions A–D and is supplied as a factory-calibrated set of three elements.

Banner Engineering IAT210S glass fiber optic sensor cable with diffuse-reflective sensing. Features a right-angle brass sensing end, stainless steel monocoil sheathing, 3.2 mm glass fiber core, and 4.572 m length. Designed for use with a separate fiber optic amplifier.

ABB S201-K1 miniature circuit breaker set consisting of two single-pole 1 A MCBs from the System pro M compact S200 series. Each breaker features a K tripping characteristic and is designed for DIN-rail mounting in AC or DC electrical installations.

Fluke i200 AC current clamp enables accurate 0.5–200A AC measurements using a multimeter. Features 1 mA/A output, banana plug interface, and CAT III 600V safety for electrical testing.

The Allen-Bradley AK-R2-360P500 Dynamic Brake Resistor is an external medium-duty resistor kit designed for PowerFlex 70 and 700 series drives. It provides 360 ohms of resistance with an 86 watt continuous power rating to dissipate regenerative energy during motor braking.

The KAMAN Sensors digiVIT 855949-000 is a self-tuning digital driver for non-contact inductive and eddy current position and displacement sensors. It features pushbutton calibration, embedded intelligence, selectable analog outputs, and Ethernet connectivity for monitoring and parameter switching.

Fluke 302+ digital clamp meter delivers reliable 400A AC current and 600V AC/DC measurements in a compact handheld design with backlit display, built for everyday electrical troubleshooting and maintenance tasks.

The Honeywell 621-9938RC is a dual-port Serial I/O Module for the IPC 620/621 Programmable Controller System. It provides redundant serial communication, configurable I/O point allocation, DIP switch configuration, front status LEDs, and supports hot-swappable operation in redundant serial I/O architectures.

The Siemens 3SU1400-1AA10-1BA0 is a SIRIUS ACT contact module with one normally open contact. It features screw terminals and a snap-on design for front plate mounting behind compatible actuators. Designed for industrial control and signaling applications requiring reliable signal switching.

The Edwards Signaling 48XBRMG120A is a green LED visual signal light designed for indoor and outdoor industrial applications. Operating on 120 VAC, this dual-mode beacon supports steady-on or flashing operation and is housed in a corrosion-resistant NEMA 4X enclosure.

Mersen A050F300 Protistor semiconductor fuse delivers ultra-fast aR protection at 500V and 300A, designed to limit let-through energy and protect sensitive power electronics in high-performance drive and converter systems.

The MEAN WELL HRP-600-15 is a single-output enclosed AC-DC power supply delivering 15 VDC at up to 43 A. It features built-in active power factor correction, fan cooling with ON-OFF control, and protection against overload, over-voltage, and over-temperature for industrial power applications.

Turck BI10-G30SK-RZ3X2 inductive proximity sensor with 10 mm rated switching distance. M30 threaded, flush-mount metal housing with terminal chamber connection. Supports 20–250 VAC and 10–300 VDC operation with 2-wire NC output for industrial metal detection.

The Phoenix Contact 560-3889 is a power distribution interface module used within Emerson Ovation distributed control systems. It functions as a marshalling and power distribution interface between controllers and I/O field devices, supporting structured wiring through screw terminal connections in PLC and DCS panels.

Pomona 1296 BNC male to dual stacking binding post adapter converts BNC test instruments to banana jack connections, supporting stacked binding posts for flexible laboratory and bench testing setups.

The Allen-Bradley 800T-XA2 Series D is a 30 mm industrial control contact block featuring two normally open contacts and an A600 NEMA pilot duty rating. Designed for use with Bulletin 800T operators, it provides screw-terminal connections and base-mount installation for industrial control panels.

Fluke Networks GLD-DSX-5000MI Gold Support delivers 1-year maintenance for DSX-5000 systems, including 24/7 technical support, software and firmware updates, calibration, repairs, and parts replacement.

Fluke Networks GLD3-OFP-MOD-Q Gold Support provides 3-year maintenance coverage for OFP-QUAD modules, including calibration, repairs, parts replacement, software updates, and 24/7 technical support for reduced downtime.

Fluke LENS/4XTELE2 4X Telephoto IR Smart Lens magnifies distant targets for safer thermal inspections without recalibration on compatible Fluke cameras.

Fluke Networks GLD-CFP-100-SI provides 1 year Gold Support for the CFP-100-SI CertiFiber Pro, including 24/7 technical support, calibration, firmware updates, parts replacement, and express service coverage.